MPU 6050 QFN-24 3-Axis Gyro/Accelerometer IC

369.00

  1. User-programmable digital filters for gyroscope, accelerometer, and temp sensor
  2. Digital-output temperature sensor
  3. 9-Axis Motion Fusion by the on-chip digital motion processor (DMP)
  4. Auxiliary master I2C bus for reading data from external sensors
  5. Minimal cross-axis sensitivity between the accelerometer and gyroscope axes
  6. MEMS structure hermetically sealed and bonded at the wafer level
  7. 10,000 g shock tolerant
  8. 400kHz fast mode I2C for communicating with all registers
SKU: RK000231 Category:

Description

The MPU 6050 QFN-24 3-Axis Gyro/Accelerometer IC incorporates Intenseness’s Motion Fusion and run-time calibration firmware that enables manufacturers to eliminate the costly and complex selection, qualification, and system level integration of discrete devices in motion-enabled products, and guarantees that sensor fusion algorithms and calibration procedures deliver optimal performance for consumers.
.The MPU-6050 is a serious little piece of motion processing tech! By combining a MEMS 3-axis gyroscope and a 3-axis accelerometer on the same silicon die together with an onboard Digital Motion Processor™ (DMP™) capable of processing complex 9-axis Motion Fusion algorithms, the MPU-6050 does away with the cross-axis alignment problems that can creep up on discrete parts. The parts’ integrated 9-axis Motion Fusion algorithms can even access external magnetometers or other sensors through an auxiliary master I2C bus, allowing the devices to gather a full set of sensor data without intervention from the system processor.

For precision tracking of both fast and slow motions, the MPU-6050 features a user-programmable gyro full-scale range of ±250, ±500, ±1000, and ±2000°/sec (dps) and a user-programmable accelerometer full-scale range of ±2g, ±4g, ±8g, and ±16g.

Features: 

  • User-programmable digital filters for gyroscope, accelerometer, and temp sensor
  • Digital-output temperature sensor
  • Auxiliary master I2C bus for reading data from external sensors
  • Minimal cross-axis sensitivity between the accelerometer and gyroscope axes
  • MEMS structure hermetically sealed and bonded at the wafer level
  • 400kHz fast mode I2C for communicating with all registers
  • Applications: Consumer Electronics, Sensing & Instrumentation, Automation & Process Control, System Monitoring, Robotics.
  • Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
  • Tri-Axis accelerometer with a programmable full-scale range of ±2g, ±4g, ±8g and ±16g
  • Reduced settling effects and sensor drift by the elimination of board-level cross-axis alignment errors between accelerometers and gyroscopes
  • 9-Axis Digital Motion Processing (DMP) engine offloads complex Motion Fusion, sensor timing synchronization and gesture detection
  • Embedded algorithms for run-time bias and compass calibration. No user intervention required
  • Digital-output temperature sensor
  • Digital input on FSYNC pin to support video Electronic Image Stabilization and GPS

    Programmable interrupt supports gesture recognition, panning, zooming, scrolling, free fall interrupt, high-G interrupt, zero-motion detection, tap detection, and shake detection

  • VDD Supply voltage range of 2.375V–3.46V
  • VLOGIC at 1.8V±5% or VDD
  • On-chip timing generator with ±1% frequency variation over the full temperature range
  • 10,000g shock tolerant.

Package Includes:

1 x MPU 6050 QFN-24 3-Axis Gyro/Accelerometer IC

Reviews

There are no reviews yet.

Be the first to review “MPU 6050 QFN-24 3-Axis Gyro/Accelerometer IC”

Your email address will not be published. Required fields are marked *