Sale!

Orange 360 PPR 2-Phase Incremental Optical Rotary Encoder

Original price was: ₹1,599.00.Current price is: ₹1,571.00.

  1. Encoder Type: Optical
  2. IP52 (IEC Standard) Protection
  3. Stainless Steel Shaft
  4. High-quality 2-Meter Cable
  5. Anti-jamming Performance
  6. 2-Phase precise Output Readings

Out of stock

SKU: RK0010055 Categories: ,

Description

If you want to build a project where the machine can control the speed of the conveyer belt as well as the direction of movement, a rotary encoder is a must-have component. Keeping this in mind, robotools.in is introducing the brand new orange 400 PPR 2-Phase Incremental Optical Rotary Encoder at a competitive price.

A rotary encoder is a type of position sensor which is used for determining the angular position of a rotating shaft. It generates an electrical signal, either analog or digital, according to the rotational movement.

Orange 360PPR Incremental Optical Rotary Encoder is a hi-resolution encoder with quadrature outputs for increment counting. It will give 1440 transitions per rotation between A and B outputs.  A quadrature decoder is required to convert the pulses to an up count. The Encoder is built to Industrial grade.

The Encoder comes with a Standard 1.5 m cable length which can be extended with extra cable if needed.

Consider Adding Pull up resistor to both the A and B phases of the encoder output to avoid the effect of interference in output and get the precise logical output value from the encoder. Also adding a pull-up resistor to all phase output lines protects the open collector output-triode from damage due to direct Vcc supply short circuit.

Note: A sample tutorial code has been given in the Description  Section.


Power and Input Terminal Assignments:
Terminal NameWire ColorDescription
Phase AWhiteQuadrature encoded output A
Phase BGreenQuadrature encoded output B
VCCRedVCC should be connected to +ve 5V of supply
GNDBlackThe ground should be connected to the negative supply
ShieldGoldenThe shield should be connected to GND

Shielding is important. At a minimum, the cable should be protected either by a foil jacket with a drain wire or by a braided-wire shield that is grounded. For very sensitive applications or high-EMI environments, foil jacketed wires in combination with an overall braided-wire shield around the cable should be used to avoid interference and precise encoder output.

To Explore More Rotary Encoders, Click here


Features :

  1. High cost-efficient advantages.
  2. Incremental rotary encoder internal adopts ASIC devices
  3. High reliability, long life
  4. Anti-jamming performance
  5. Small size, lightweight, compact structure
  6. Easy installation
  7. Stainless steel shaft, High resolution, High quality, line interface with waterproof protection

Tutorial Code:

//these pins can not be changed 2/3 are special pins
int encoderPin1 = 2;
int encoderPin2 = 3;

volatile int lastEncoded = 0;
volatile long encoderValue = 0;

long lastencoderValue = 0;

int lastMSB = 0;
int lastLSB = 0;

void setup() {
  Serial.begin (9600);

  pinMode(encoderPin1, INPUT); 
  pinMode(encoderPin2, INPUT);

  digitalWrite(encoderPin1, HIGH); //turn pullup resistor on
  digitalWrite(encoderPin2, HIGH); //turn pullup resistor on

  //call updateEncoder() when any high/low changed seen
  //on interrupt 0 (pin 2), or interrupt 1 (pin 3) 
  attachInterrupt(0, updateEncoder, CHANGE); 
  attachInterrupt(1, updateEncoder, CHANGE);

}

void loop(){ 
  //Do stuff here

  Serial.println(encoderValue);
  delay(1000); //just here to slow down the output, and show it will work  even during a delay
}


void updateEncoder(){
  int MSB = digitalRead(encoderPin1); //MSB = most significant bit
  int LSB = digitalRead(encoderPin2); //LSB = least significant bit

  int encoded = (MSB << 1) |LSB; //converting the 2 pin value to single number
  int sum  = (lastEncoded << 2) | encoded; //adding it to the previous encoded value

  if(sum == 0b1101 || sum == 0b0100 || sum == 0b0010 || sum == 0b1011) encoderValue ++;
  if(sum == 0b1110 || sum == 0b0111 || sum == 0b0001 || sum == 0b1000) encoderValue --;

  lastEncoded = encoded; //store this value for next time
}

Package Includes :

1 x Orange 360PPR 2-Phase Incremental Optical Rotary Encoder

4 x 4.7KΩ Resistors for pull-ups

1 x Mounting Screw Set

Reviews

There are no reviews yet.

Be the first to review “Orange 360 PPR 2-Phase Incremental Optical Rotary Encoder”

Your email address will not be published. Required fields are marked *